Baumuller BUS6-VC-A0-0001-0013-0000-0000
€ 1.192,00
Baumuller repareren bij Cirele is:
• Duidelijke tarieven zonder onverwachte kosten
• Betaling pas na geslaagde reparatie
• Proactieve vervanging van tijdgevoelige onderdelen
• Gedetailleerd test- en reparatierapport wordt verstrekt
• 2 jaar garantie op alle reparaties
• Langdurige ondersteuning tot einde levensduur.
Heeft uw Baumuller BUS6-VC-A0-0001-0013-0000-0000 een defect of werkt het niet naar behoren? Wij voeren vakkundige reparaties uit en kunnen het product op bestelling leveren: nieuw, gebruikt of refurbished. Wij repareren de elektronica op locatie of in onze eigen werkplaats.
Heeft u spoed? Maak gebruik van onze speciale spoedlijn voor een snelle oplossing.
| Condition |
|---|
Common defects
Common defects on a Baumuller BUS6-VC-A0-0001-0013-0000-0000 are:
Power Supply Related Issues
- No power / drive not turning on
- Blown fuses
- Defective rectifier bridge
- Damaged DC bus capacitors
- IGBT / MOSFET module failure
- Overvoltage / undervoltage errors
Control & Electronics Failures
- Faulty control board or PCB damage
- Firmware or memory corruption
- Fieldbus communication errors (Profibus, Modbus, EtherCAT, CANopen)
- Input / output circuit damage
- Gate driver module failure
Motor Control Problems
- Motor not starting or no output
- Unstable speed control
- No torque output
- Trip during acceleration or deceleration
- Encoder feedback errors
Thermal & Cooling Defects
- Overheating due to failed cooling fans
- Defective temperature sensors
- Poor heatsink performance
Mechanical & Environmental Damage
- Burnt or loose connectors
- PCB track damage
- Corrosion or moisture ingress
- Oil, dust or contamination damage
- Cracked solder joints
Error Codes & Drive Trips
- Overcurrent faults (OC)
- Ground fault / earth leakage error
- Short-circuit fault
- Motor or drive overload
- Overvoltage or undervoltage error
- Undervoltage trip when starting or stopping
- Phase loss / imbalance
- Synchronization issues with multiple drives
Other
- Display defect
- Control keys or keypad not working
- Parameters no longer readable or lost
- Brake resistor problems (brake chopper defect)
- Internal relays/contactors defective
- EMI/RFI interference due to defective filters
Common defects
Common defects on a Baumuller BUS6-VC-A0-0001-0013-0000-0000 are:
- Damaged or broken housing
- Unresponsive or defective touchscreen (repair or replacement)
- Defective display or LCD screen (repair or replacement)
- Damaged protective film
- Backlight failure
- Power supply problems
- Defective or damaged circuit board (incl. component replacement)
- Defective communication ports (LAN, Profibus, MPI, serial, CAN)
- Software issues (failure to start, backup creation, software recovery)
Related products
-
Siemens HMI 6AV3607-1NH00-0AX0
€ 549,00Repair at Cirele is:• Fixed price, no surprises afterwards• Payment only upon successful repair• Time-sensitive components are replaced preventively• You will receive a test and repair report• 2 year warranty on the repair• Support up to end of life.Siemens TP7 Touch Panel
-
Siemens HMI 6AV6640-0CA11-0AX0
Price range: € 375,00 through € 1.055,00Repair at Cirele is:• Fixed price, no surprises afterwards• Payment only upon successful repair• Time-sensitive components are replaced preventively• You will receive a test and repair report• 2 year warranty on the repair• Support up to end of life.Siemens SIMATIC Touch Panel TP 177MICRO for SIMATIC S7-200 5.7″ Blue Mode STN Display Configurable WinCC Flexible 2004 Micro HSP upwards; contains open-source-SW, which is provided free of charge. For details see enclosed CD.
-
Siemens HMI 6AV6545-8CC10-0AA0
€ 1.224,00Repair at Cirele is:• Fixed price, no surprises afterwards• Payment only upon successful repair• Time-sensitive components are replaced preventively• You will receive a test and repair report• 2 year warranty on the repair• Support up to end of life.Siemens SIMATIC Touch Panel TP 270 10.4″ color STN display, Touch Stainless steel front, Continuous decorative film, Degree of protection front IP66 Windows CE 3.0 configurable with ProTool Version V6.0+SP2 or higher
